Unloading and conveying FIBCs of titanium dioxide for the ink and coatings industry

The first part of this industrial installation centered around a station that would allow the emptying and discharging of bulk materials from 1-ton super sacks and 50 lbs. paper bags. The height of the installation was restrictive; therefore, our team of industrial engineers designed a solution that allowed a low-height structure for installation on the client’s second floor mezzanine. By combining the functions of both a sack tip tray / bag dump station for 50 lbs. sacks into the same footprint of a bulk bag unloader, a considerable floor space was saved. An electrical hoist was installed directly onto a support rafter that was validated and designed to handle the extra load of lifting and transferring 1 ton bulk bags. With these established features, the client was able to fit the powder handling equipment within their confined work area.

Manufacturer’s who handle TiO2 know all to well that this powder tends to have poor flow characteristics. The powder tends to cling to itself, clumping up causing bridging and rat-holing issues over discharge outlets of hoppers, silos and IBCs. Our powder processing team took further steps to remedy any potential flow issues coming out of the super sack. One such feature is a telescoping flexible discharge chute with a clamping connection plate. By clamping the bulk bag’s outlet spout, the telescoping tube can provide a minimal downward pulling action to help stretch the spout and cause a funneling effect on the bottom corners of the bulk bag. This downward pulling action helps create a sloping angle on the bottom side of the FIBC to further promote the flow of the clumping powder. Furthermore, massage paddles are built into the bottom corners of the bulk bag tray. These paddles are attached to pneumatic actuators and can lift and squeeze the bottom corners of the bulk bag. This action can help break up material bridging to further promote the flow of the bulk powder.

Underneath this spout clamping plate is a built-in bag dump station. Also called sack tip trays, this unit contains a safety grid that allows an operator to place an entire 50 – 100 lbs paper sack of TiO2 inside the cabinet. The operator then can use his utlitity knife, secured to the inside of the cabinet, to cut open the bag and pour out the contents.

In order to transfer the TiO2 powder from the super sack emptying station to the main solvent reactor, our team employed the use of a mechanical auger conveyor, also called a screw conveyor. This industrial machine is responsible for the powder transfer to the downstream production process. This type of powder conveying equipment is excellent for both the transfer of and controlled metering of bulk solids and dry materials. The inlet is bolted to the bottom flange of the bulk bag hopper and consists of a direct drive motor attached to a tubular housing. Inside the tube is an auger with spiral flights which cause the forward momentum of the powder and bulk solids. It is designed to handle a throughput rate of 18,000 lbs/hr. The length between the inlet and outlet is approximately 60” with a tube diameter of 11”.

Screw conveyors are great for continuous powder feeding applications with their robust design that allows them to work with light, medium or heavy-duty industrial applications. Because of its mechanical agitation technique, auger conveyors are also well suited for powders that tend to clump and have poor flow properties.

When designing a control panel for a NEC NFPA 70 rated hazardous area is to first see if it is possible to install it outside the zone or room. If not, the next step is to explore options for either air purge or pressurized cabinet methods, or, a 10-bar rated bolted panel.
For this project, we used a Ex control panel designed and built to operate in environments where concentrations of flammable gases, vapors, liquids or combustible particles pose risks of ignition and explosion. The explosion proof control panel enclosures are cast from heavy duty aluminum so that they cannot create a spark that could possibly ignite the vapors in a hazardous location. These heavy-duty panels come with seals to keep explosive fumes from entering the control panel. Also, the explosion proof control panels are designed to contain an internal explosion without igniting the explosive vapors present in the hazardous area to make sure it is safe for the hazardous classification 1 / division 2 zone. Explosion proof panels are built with robust metal walls to allow the containment of internal explosions from components and the sustainment of external explosions. Fittings, glands, and other system components will be ensured to have the appropriate rating for the hazardous area standards.

Palamatic Process has been supplying the powder and bulk solids industry with bulk bag handling equipment since 1992. In order to determine what solution is best for your project, contact one of our sales engineers. Together, our team of experts can provide the right kind of powder filling equipment that will meet your production goals.
Contact one of our experts today for assistance with needed material handling solutions and to request a quote.